Position:
Home > FAQ
FAQS
We have our own brand, and the products has passed the ISO9001 quality system and CE certification, and all the equipmentfittings are famous brand in China.
How to install the rotary vibrating screen correctly
1. Install the damping rubber pad
In order to avoid the movement of the vibrating screen during operation and reduce noise, the three damping rubber pads in the accessories should be installed on the bottom of the base of the vibrating screen during installation, and the vibrating screen must be fixed with anchor screws; 2. Net installation and removal
①. The screen of the rotary vibrating screen should be installed on the screen frame. To install or disassemble the screen, the screen ring (frame) should be removed first, and the discharge port should be placed on the platform, and then the screen frame should be lowered. Put the screen on the screen frame, then put the screen compression ring, and fix it slightly symmetrically with the screws according to the vertical direction of the screen. After confirming that the screen has no creases, is evenly elastic, and has a square shape of the screen holes, respectively insert the screws into the screw holes. In the middle, slowly and evenly rotate and tighten one by one, and finally cut off the excess screen.
②. Because the screen frame and the screen pressing ring are designed with a dovetail groove structure, the more you press the screen, the tighter the screen will be to ensure that the screen is tight; if the customer has no special requirements, the screen frame is usually made of aluminum alloy, and the screen There is a certain range for the gap between the pressing ring of the grid frame and the screen frame. If it is an extra-coarse screen, the gap should be increased. If it is not in place, tap it gently and evenly with a wooden hammer, or use a vise to tighten the edge. When screwing the screws, special care should be taken during this process, so as not to cause the pressing ring of the screen frame to break.
③. According to the requirements of the materials to be screened, the mesh number of the screen should be selected, the lower layer is for the larger mesh number, and the upper layer is for the smaller mesh number. It is necessary to ensure that the mesh number of the screen is selected correctly. If the mesh number is not standard, it will affect the production quality. In addition, the screen with a larger mesh is lighter and thinner, and a screen with a smaller mesh should be lined underneath to prolong the service life of the screen.
④. The screen is a vulnerable part. During the use of the rotary vibrating screen, it should be regularly checked for broken wires, leaks, depressions, deformation and other damages. If the screen is damaged, it should be replaced in time to avoid accidents. The breakage of the screen causes the rubber ball to fall into the material.
3. Precautions for use of screen bottom, rubber ball and sealing strip
There are rubber balls placed on the bottom of the screen. Due to the vibration of the rotary vibrating screen, the rubber balls are forced to bounce and move continuously along the circumferential direction on the bottom of the screen to achieve the purpose of cleaning the screen and also to ensure the screening output and accuracy. , During the use of the rotary vibrating screen, certain wear and tear will also occur. It should be checked regularly and replaced if necessary to prevent it from falling into the material. The backing is fixed on the screen frame by screws. Long-term vibration will cause the screws to loosen or even fall into the material. Therefore, it should be checked regularly, and if it is loose, it should be tightened in time.
The main function of the sealing strip of the rotary vibrating sieve is to prevent the latent leakage of the material. It should be checked regularly. If there is inelasticity due to long-term compression, it should be replaced in time to prevent the occurrence of latent powder leakage.
4. Adjustment of excitation force and amplitude
①. By adjusting the phase angle of the weight block or increasing or decreasing the weight block, the rotary vibrating screen can produce different exciting forces and amplitudes, so as to change the movement track of the material, so that the material can be fully vibrating and screened on the screen surface , so as to meet the screening requirements of different materials and achieve the highest screening accuracy and output.
②. Changing the angle of the weight can change the movement track of the material. Loosen the weight block and tighten the screw to move the weight faster, and then tighten the clamping screw after making the required angle relative to the dial. The smaller the included angle, the greater the exciting force. Usually the included angle should not exceed 90°.
③. The adjustment of the amplitude can be divided into two aspects: horizontal and vertical. The size of the amplitude directly affects the output of the screening. (This article is provided by Xinxiang Machinery Co., Ltd.) The increase of the horizontal amplitude makes the materials on the screen move to the edge faster, and the vertical amplitude The increase makes the material on the sieve bounce stronger. The amplitude of the vibration is adjusted by adjusting the weight of the upper and lower weights. The amplitude should not exceed a certain range, otherwise it will affect the service life of the rotary vibrating screen.
5. Adjustment of the outlet position
The position of each discharge port of the rotary vibrating screen can be adjusted according to the site conditions of the user. The adjustment method is very simple. Remove the fastening lock and change the position of the discharge port according to the circumferential direction. After confirming the position, install the fastening lock. .
How can the grain suction machine be used safely
Grain suction machine is an automatic equipment for transporting materials, in the process of use must be familiar with the operating procedures and in accordance with the requirements to do a good job, so as to ensure the safe use of the machine, the following is the correct use of grain suction machine need to pay attention to.
Not to be able to open the equipment at will, the use of grain suction machine should obey the workshop in charge of management, and in accordance with the operating procedures. Without the consent of the supervisor, do not touch and open various switches at will.
Wear suitable clothes to operate the equipment, do not wear shorts skirt, long hair should be coiled up, do not wear slippers, so as to ensure the safety of the operation of the suction machine.
Before turning on the grain suction machine must check whether the equipment is normal and whether the power connection conditions meet the requirements. If there is a problem with the equipment needs to be serviced, not blindly start.
Feeding and running are to closely observe the condition of the grain suction machine, a failure to stop in time.
Grain suction machine go material speed control, not too fast or too slow.
Do not arbitrarily adjust the parameters of the equipment, all aspects of the parameter settings are clear requirements, unauthorized changes may bring safety hazards.
So, want to ensure the safe use of grain suction machine, then the above points should pay attention to a little, can not be ignored!
How to choose a suitable rotary vibrating screen or linear screen to meet production needs?
1. Selection according to material characteristics: Different materials require different types of vibrating screens. For the rotary vibrating screen, it can screen and remove impurities from 0-400 mesh powdery and granular materials. If it is used for filtering, it can filter materials below 600 mesh;
Requirements for use: The material is not viscous, has no static electricity, is not easy to agglomerate, and has uniform particles.

2. Selection according to production conditions: Different production environments also have an impact on the selection of rotary vibrating screens. Space requirements, installation location requirements, etc. can affect the size and output of the screen machine.
How to calculate the conveying capacity of the screw conveyor?
1. Calculation of spiral diameter:

In the formula, Q----conveying capacity, t/h;

K——material property coefficient;

ψ----filling factor;

C ---- tilt coefficient.

The diameter calculated by the above formula should be rounded up;

2. Calculation of screw shaft speed:

The screw shaft speed n cannot exceed a certain limit speed nj

In the formula, A----represents the material comprehensive coefficient;

The A value corresponds to the K value, and should be selected in groups during calculation.

3. Power calculation:

(1) Screw conveyor shaft power P0

H——the projected height of the screw conveyor on the vertical plane when it is inclined, m;

L - the horizontal projection length of the screw conveyor, m;

ω0----material resistance coefficient.

(2) Motor power

K1----power reserve coefficient, Y series motor K1=1.0;

η--the total efficiency of the driving device, generally 0.9-0.94.
How Often Do Screw Conveyors Need Cleaning and Maintenance?
Regular inspection: Before and after use every day, the conveyor should be inspected to check whether the appearance of the conveyor, transmission parts, support parts and electrical equipment are normal, and whether there are abnormal noises, etc., to avoid failures and accidents.

Regular lubrication: According to the frequency of use and working environment of the conveyor, use appropriate lubrication methods and lubricating grease to lubricate the bearings, gears, chains and other parts of the conveyor to ensure smooth operation and low noise of the conveyor.

Regular cleaning: According to the characteristics of the conveying materials and the use of the conveyor, the conveyor is regularly cleaned to remove dust, sundries, oil stains, etc. inside and outside the conveyor, so as to avoid affecting the operation of the conveyor and the quality of the conveying materials. Influence.
How to reasonably select the rotary vibrating screen mesh? Control the particle size of the sieve by controlling the mesh size
Everyone knows that whether it is a rotary vibrating screen or a linear vibrating screen, the most important thing when screening materials is the screen mesh. The screening of materials is controlled by the mesh size on the vibrating screen, and the effective selection of the mesh is the main factor in improving the efficiency of the vibrating screen! Today, the editor will organize how to reasonably select the screen mesh for the rotary vibrating screen. I hope the majority of users can be helpful.



1. The aperture of the rotary vibrating screen mesh refers to the size of the standard screen mesh, and the wire diameter of the screen mesh refers to the diameter of the woven metal wire.



2. Mesh size refers to the number of mesh holes in a length of 2.54 centimeters (1 inch), abbreviated as mesh size. For example, 80 mesh means that there are 80 holes per square inch, and 700 mesh means 700 holes. The higher the mesh count, the more holes there are. In addition to representing the mesh size of the sieve, it is also used to represent the particle size that can pass through the sieve. The higher the mesh size, the smaller the particle size.



3. The conversion method between mesh size and aperture micrometer of the sieve: Generally, in China, the grading system is based on the Taylor sieve system, with a 200 mesh mesh size of 0.074mm as the benchmark. The 100 mesh aperture is 200 * 0.074mm ÷ 100=0.148mm/325 mesh aperture is 200 * 0.074mm ÷ 325=0.045mm/.

4. The size of powder particles is called particle size. Due to the complex shape of particles, there are usually several representation methods, such as screening particle size, settling particle size, equivalent volume particle size, and equivalent surface area particle size. Sieve size refers to the size of the sieve holes through which particles can pass through the sieve, expressed as the number of sieve holes within a 1-inch (25.4mm) wide sieve. Therefore, it is called "mesh size". Currently, there is no unified technical standard for powder particle size at home and abroad, and each enterprise has its own definition and representation method for particle size. The specifications of screens in different countries and industries have different standards, so the meaning of "mesh" is also difficult to unify.

5. At present, the calculation diameter of equivalent volume particles is commonly used internationally to represent particle size. with μ Represented by m or mm.

6. The customer specifies the number of mesh sizes and has strict requirements or industry requirements that must comply with international standards. Customers are required to specify the corresponding mesh size. The mesh size is the only standard, but there are multiple options for mesh size.

Due to the inconsistency in the mesh size and aperture of the screening machine, users should choose the screening mesh based on the characteristics of their own materials. There is nothing absolute about choosing a sieve, we can only say that we can make the sieve machine and sieve match perfectly.
welconme
your inquiry
Copyright © Xinxiang Dayong Vibration Equipment Co., LTD.
Technical Support: COVERWEB