Usage of vibrating screen
1. Installation of vibrating screen: Firstly, it is necessary to ensure that the installation position of the vibrating screen meets production requirements and determine the installation method based on on-site conditions. Generally speaking, the vibrating screen can be installed above the silo, below the storage tank, or other appropriate positions.
2. Adjusting the amplitude and frequency of the vibrating screen: Before using the vibrating screen, it is necessary to adjust the amplitude and frequency of the vibrating screen to ensure the screening effect and production efficiency of the materials. The amplitude can usually be adjusted by changing the size of the screen, while the frequency can be adjusted by changing the speed of the motor.
3. Start the vibrating screen: Before starting the vibrating screen, it is necessary to ensure that the motor and reducer have been installed correctly, and check whether the connection between the screen and the motor is secure. Next, you can press the switch to start the motor and observe the operation of the vibrating screen.
4. Adjusting the amplitude and frequency of the vibrating screen: When using the vibrating screen, it is necessary to adjust the amplitude and frequency in a timely manner based on the characteristics of the material and production needs. Generally speaking, the finer the particles of the material, the smaller the amplitude and the higher the frequency.
5. Cleaning the vibrating screen: After using the vibrating screen, it is necessary to clean the screen and reducer in a timely manner to ensure the normal operation of the equipment and production safety. Water or cleaning agents can be used for cleaning, but corrosive chemicals must not be used.

Vibrating screens can be applied in many industries, such as mining, construction, chemical, pharmaceutical, food processing, etc. The following are some common applications of vibrating screens:

1. Mining: Vibrating screens can be used to screen materials such as ore, coal, limestone, etc. to ensure the quality and purity of the materials
2. Architecture: The vibrating screen can be used to screen building materials such as concrete, sand, and stones to ensure the quality and uniformity of the materials.
3. Chemical industry: Vibrating screens can be used to screen chemicals, coatings, paints, pigments, and other materials to ensure the quality and purity of the materials.
4. Pharmaceutical: The vibrating screen can be used to screen materials such as drugs, vaccines, and syrups to ensure the quality and purity of drugs.
5. Food processing: The vibrating screen can be used to screen materials such as flour, sugar, starch, and milk powder to ensure the quality and uniformity of the materials.

The impurities mixed in mung beans are generally stones, dust, weeds, etc. If you want to get rid of these impurities, a linear vibrating screen is the first choice for removing these impurities. The main reasons for choosing a linear vibrating screen are the following:

1. The linear vibrating screen has a large output and high efficiency. Generally, the output of the linear vibrating screen can be between 1 and 10 tons per hour. Compared with the rotary vibrating screen, the large output of the linear vibrating screen is more suitable for the needs of manufacturers.
2. The linear vibrating screen has a simple structure and is easy to maintain. For the equipment with simple structure for the production line, if there is a problem, it can be repaired in time, and the fault is checked.
3. The full-closed structure of the linear vibrating screen, the dust will not fly, because there are dust and other impurities in the mung bean, the full-closed structure can prevent the dust from flying in the workshop and protect the clean environment of the workshop.

For screw conveyors used in metallurgy, mining and chemical industries, the shaft end gland is widely sealed with packing. Because the particle size of the coal powder is 200 mesh, it is in the form of fine powder and has a certain fluidity, so it is often because the shaft end of the screw conveyor head is not tightly sealed and many coal powders are leaked. Although asbestos packing, oil-impregnated asbestos rope and flexible graphite ring are also used as sealing packing, the leakage control effect is not ideal. Pulverized coal leaks around the equipment every day, which wastes and pollutes the environment and affects civilized production. In order to solve this problem, the following method hopes to be useful to you.
1.Lubricating grease must be added into the gland every 3-4 days, otherwise the coal powder will still be leaked or the coal powder will leak out
2.After each installation and disassembly, the gland bolts must be tightened for about one month after starting up, so that the packing and the shaft closely fit together. But it is not necessary to press too tightly, the gland bolts can be adjusted according to the actual situation.

The frequency of checking the tension of the vibrating screen's belts will depend on several factors, such as the screen's usage frequency, the load it handles, and the manufacturer's recommendations.

Generally, it is recommended to check the tension of the belts on a regular basis, such as once a month, to ensure that they are properly tensioned and do not show any signs of wear or damage. If you notice any signs of wear, such as cracks, fraying, or stretching, the belts should be replaced immediately to prevent further damage and potential failure.

It's also important to keep in mind that belts can wear out over time due to regular use and exposure to environmental factors. Therefore, even if there are no visible signs of wear, it may be necessary to check the tension of the belts periodically to ensure optimal performance of the vibrating screen. The manufacturer's recommendations regarding belt tensioning and maintenance frequency can also provide guidance on when to check the belt tension.

In addition to regular checks of the belt tension, it's important to maintain proper tension on the belts to ensure that the screen operates smoothly and efficiently. Improperly tensioned belts can cause the screen to vibrate excessively, leading to premature wear and potential damage. Be sure to follow the manufacturer's recommended tensioning procedure to ensure proper operation of the screen.

The manufacturer's recommended tensioning procedure for the vibrating screen's belts will depend on the specific model of the screen and the type of belts being used. However, here are some general guidelines for tensioning the belts:

1. First, ensure that the screen is turned off and disconnected from the power source.

2. Locate the belt tensioner, which is typically a spring-loaded pulley located near the motor.

3. Use a tension gauge or other appropriate tool to measure the tension of the belts.

4. Adjust the tensioner as needed to achieve the manufacturer's recommended tension. This may involve adjusting the tensioner bolt or moving the tensioner pulley to increase or decrease tension.

5. Check the tension of the belts again after making adjustments to ensure that they are within the recommended range.

6. Once the proper tension has been achieved, tighten the tensioner bolts or lock nuts to secure the tensioner in place.

7. Verify that the screen is operating smoothly and efficiently before resuming use.

It's important to note that these are general guidelines, and the specific tensioning procedure may vary depending on the model of the vibrating screen and the manufacturer's recommendations. Always refer to the user manual or contact the manufacturer for specific instructions and recommendations.
The manufacturer's recommended tensioning procedure for the vibrating screen's belts will depend on the specific model of the screen and the type of belts being used. However, here are some general guidelines for tensioning the belts:

1. First, ensure that the screen is turned off and disconnected from the power source.

2. Locate the belt tensioner, which is typically a spring-loaded pulley located near the motor.

3. Use a tension gauge or other appropriate tool to measure the tension of the belts.

4. Adjust the tensioner as needed to achieve the manufacturer's recommended tension. This may involve adjusting the tensioner bolt or moving the tensioner pulley to increase or decrease tension.

5. Check the tension of the belts again after making adjustments to ensure that they are within the recommended range.

6. Once the proper tension has been achieved, tighten the tensioner bolts or lock nuts to secure the tensioner in place.

7. Verify that the screen is operating smoothly and efficiently before resuming use.

It's important to note that these are general guidelines, and the specific tensioning procedure may vary depending on the model of the vibrating screen and the manufacturer's recommendations. Always refer to the user manual or contact the manufacturer for specific instructions and recommendations.